Experimental Study on Doweled Expansion Joints on Behavior for Plain Concrete Pavement System
This paper deals with load-deflection behavior the jointed plain concrete pavement system using steel dowel bars as a mechanism to transmit load across the expansion joints. Experimentally, four models of the jointed plain concrete pavement system were made, each model consists of two slabs of plain concrete that connected together across expansion by two dowel bars and the concrete slab were supported by the subgrade soil. Two variables were dealt with, the first is diameter of dowel bar (12, 16 and 20 mm) and the second is type of the subgrade soil, two types of soil were used which classified according to the (AASHTO): Type I (A-6) and type II (A-7-6). Experimental results showed that increasing dowel bar diameter from 12 mm to 20 mm has a little effect on load-deflection behavior of the tested specimens with only 5% increase in failure load. This may be attributed to that the failure (caused by flexural crack) depends mainly on concrete strength. Results also showed that decreasing CBR value of subgrade soil from 7% to 5% decreases failure load by about 33%.
Westergaard, H. M., “Stresses in Concrete Pavements Computed by Theoretical Analysis.” Public Roads, Vol. 7, pp. 25 – 33, 1926.
Hogg, A. and Hall, A., “Equilibrium of a Thin Plate Symmetrically Loaded, Resting on an Elastic Subgrade of Infinite Depth.” Philosophical Magazine, Series 7, Vol. 25, 1938.
Pickett, G and Ray, G. K., “Influence Charts for Concrete Pavements.” American Society of Civil Engineers Transactions, American Society of Civil Engineers, Vol. 116, pp 49-73, 1951.
Chelliah Madasamy, lssam E. Harik, David L. Allen, L. John Fleckenstein, “Laboratory Testing and Analysis of Joints for Rigid Pavements.” Research Report KTC-99- 22, 1999.
American Concrete Pavement Association (ACPA), “Design and Construction of Joints for Concrete Highways.” ACPA, Skokie, IL, 24 pp, 1991.
Yoder, E. J., and M. W. Witczak. “Principles of Pavement Design” Second Edition, John Wiley and Sons, Inc., New YoIic, 1975.
Friberg, B.F., “Design of Dowels in Transverse Joints of Concrete Pavements”, Transactions, American Society of Civil Engineers. Vol.105, No. 2081, 1940.
Friberg, B. F., “Design of Dowels in Transverse Joints of Concrete Pavements.” Transactions, American Society of Civil Engineers, 105(2081), 140-161, 1938.
Huang, Y. H., “Pavement Analysis and Design.” 2nd edition, Prentice, Hall, Englewood Cliffs, New Jersey, 2004.
Ansel C. Ugural and Saul K. Fenster, “Advanced and Applied Elasticity.” Fourth edition, Prentice Hall, Upper saddle River, New Jersey, 2003.
Timoshenko, S., and Lessells, J. M., “Applied elasticity.” Westinghouse technical night school press, 1925.
Porter, M., Alberston, M., Barnes, B., Lorenz, E., and Viswanath, K., "Thermoset Composite Concrete Reinforcement." Report HR-325 Submitted to Project Development Division of the Iowa Department of Transportation and Iowa Highway Research Board, 1992.
Neville AM, “Properties of concrete.” 4th ed. Prentice Hall. Illinois, 2005.
Raphael, J., “Tensile Strength of Concrete.” ACI Materials Journal, No. 81-17, pp. 158-165, 1984.
Basim H. Al-Humeidawi,“ Evaluation of the Performance of GFRP Dowels in Jointed Plain Concrete Pavement (JPCP) for Road/Airport under the Combined Effect of Dowel Misalignment and Cyclic Wheel Load” PhD thesis, University of Manchester, USK, 2013.
ACI Committee 224, “Joints in Concrete Construction” ACI 224.3R-95, American Concrete Institute, 1995.
Witczak, M. W., Houston, W. N., & Zapata, C. E., “Correlation of CBR Values with Soil Index Properties” Development of the 2002 Guide for the Design of New and Rehabilitated Pavement Structures, Technical Report. NCHRP Project,2001.
Copyright: Open Access authors retain the copyrights of their papers, and all open access articles are distributed under the terms of the Creative Commons Attribution License, which permits unrestricted use, distribution and reproduction in any medium, provided that the original work is properly cited. The use of general descriptive names, trade names, trademarks, and so forth in this publication, even if not specifically identified, does not imply that these names are not protected by the relevant laws and regulations. While the advice and information in this journal are believed to be true and accurate on the date of its going to press, neither the authors, the editors, nor the publisher can accept any legal responsibility for any errors or omissions that may be made. The publisher makes no warranty, express or implied, with respect to the material contained herein.